Skip to main content

Videocon Air Conditioner Error Codes

 Air conditioners had been installed self diagnosis system to display the information for the units.

Videocon Air Conditioner Error Codes
Videocon Air Conditioner Error Codes
Error CodeSeIf-check code of IuminotronSeIf-check information
Indicates ''dF'' or Heating icon flashFlicker 1 time/1sDefrost indication
Fan motor picture not runningFlicker 1 time/1sAnti cold wind
E2Flicker 1 times/8sRoom temperature sensor fault
E3Flicker 2 times/8sCoil temperature sensor
E8Flicker 3 tlmes/8sOver heat protection/Defrosting
E5Flicker 6 times/8sIndoor fan fault
E7Flicker 7 times/8sExternal feedback fault
E0Flicker 3times/8sOpen the door fault
E1Flicker 4 times/8sOutdoor tube temperature sensor faults
E6Flicker 6 times/8s(EEPROM) communication failures
FFFlicker 1 times/1sNorth American environment outside temperature erceeds the scope

Note: Above self check information is commonly applicable in our most air conditioners,but some are special,you can refer to the User’s Manual for information or contact the dealer or authorized maintenance people for help.

Selection of installation positions for outdoor unit

  • To install the outdoor unit at the places which can stand the load of the machine weight and will not cause big vibrations and noises;
  • To install the unit at the places not to be exposed to rain or direct sunshine, and the places with good ventilation;
  • The noises generated from the unit will not affect the neighboring places;
  • Do not install the unit on non-metal frame;
  • Not to install the unit at the places where there might occur the generation, inflow, stay or leakage of inflammable gases;
  • Pay attention to the drainage of the condensed water from the base plate during operations;
  • To avoid the air outlet being directly against the wind.
Videocon Air Conditioner Error Codes
Videocon Air Conditioner Error Codes

Selection of installation positions for indoor unit

  • To be installed at the position where the air delivered from the unit can reach every corner of the room;
  • To avoid being affected by the outdoor air;
  • To avoid blockage to the air inlet or outlet of the unit;
  • To avoid too much oil smoke or steam;
  • To avoid possible generation, inflow, lingering or leakage of flammable gases;
  • To avoid high-frequency facilities (such as high frequency arc welders, etc.);
  • To avoid the places where acid solutions are frequently used;
  • To avoid the places where some special sprayers (sulfides) are frequently used.
  • Not to install on top of the musical instruments,TV,computer etc.valuab|e appliance.
  • Not to install a fire alarming device near the air outlet of the unit (during operation, the fire alarm device might be erroneously triggered by the warm air from the unit);

Videocon VS5C3 Series Installation And Repair Manual PDF

Comments

Post a Comment

Popular posts from this blog

Rittal Air Conditioner Error Codes

  System messages are shown on the display screen of the Comfort controller via the displays A1 to A20 and E0. Rittal Air Conditioner Error Codes Error Codes System message Possible cause A1 Enclosure door open Door open or door limit switch incorrectly positioned A2 Internal temperature of enclosure too high Cooling capacity inadequate/unit undersized. Error as a consequence of messages A03 to A17. A3 Filter monitoring Filter mat soiled A4 Ambient temperature too high/too low Ambient temperature outside of admissible operating range (+10°C to +60°C) A5 Icing hazard Operational display in case of icing hazard. A6 PSAH pressure-operated switch Ambient temperature too high A7 Evaporator coil Lack of coolant; sensor in front of or behind condenser defective. A8 Condensate warning Condensate discharge kinked or blocked A9 Condenser fan blocked or defective Blocked or defective A10 Evaporator fan blocked or defective Blocked or defective A11 Compressor Compressor overloaded A12 Condense...
Post a Comment
Read more

Midea VRF Error Codes

  R410A All DC Inverter V4 Plus R Series 50/60Hz Error Codes: V4 VRF:  Advanced 3-pipe technology enables  heat recovery  between indoor units for unprecedented economy and performance. It can simultaneously operate in cooling and heating mode when it is necessary to provide more freedom for operation. It compensates and adjusts when there are hot and cold rooms in the same building, depending on the direction of sunshine. As a result, it reduces annual power consumption. Midea VRF Error Codes Error Codes Problem E0 Communication error between outdoor units. Only display on the faulty slave unit, all the ODUs are in standby. E1 Phase sequence error. Display on the faulty unit, all the ODUs are in standby. E2 Communication error between indoors and the master unit. Only display on the master unit, all the ODUs are in standby. E4 Outdoor ambient temperature sensor (T4) and condenser pipe temperature sensor (T3/T5) error. Display on the faulty unit, all the ODUs are in ...
Post a Comment
Read more

LG VRF Error Codes – Multi V

  Error Codes; Indicate different types of unit failures, assist in self-diagnosis and to track the frequency of occurrence. Error codes are shown on the LED of indoor units, wired remote controller, the outdoor unit control board, and on the main screen of the LG Monitoring View (LGMV) Diagnostic Software. If two or more errors occur simultaneously, the lower error code number is displayed first. After error is resolved, the error code does not display. Error Display; The first, second, and third number on the LED indicates error number; the fourth number on LED indicates outdoor unit number. Examples: 211 = Error No. 21 on master unit, 213 = Error No. 21 on slave2 unit, Error No. 105 on master unit on compressor 1. Error Code Nomenclature Definitions; MICOM: Non-volatile memory chip where unit setup information is stored. EPROM: Non-volatile memory chip where device identification, size, and factory defined default component operating parameters are stored.   LG Multi V Erro...
2 comments
Read more