Skip to main content

Inventor Air Conditioner Error Codes

 

Inventor Air Conditioner Error Codes
Inventor Air Conditioner Error Codes
Code DisplayMalfunction Name
E1High pressure protection of system
E2Antifreezing protection
E3System block or refrigerant leakage
E4High discharge temperature protection of compressor
E5Overcurrent protection
E6Communication Malfunction
E8High temperature resistant protection
EEEEPROM malfunction
EULimit/ decrease frequency due to high temperature of module
C5Malfunction protection of jumper cap
FoGathering refrigerant
F1Indoor ambient temperature sensor is open/short circuited
F2Indoor evaporator temperature sensor is open/short circuited
F3Outdoor ambient temperature sensor is open/short circuited
F4Outdoor condenser temperature sensor is open/short circuited
F5Outdoor discharge temperature sensor is open/short circuited
F6Limit/ decrease frequency due to overload
F8Decrease frequency due to overcurrent
F9Decrease frequency due to high air discharge
FHLimit/ decrease frequency due to antifreezing
PHVoltage for DC bus-bar is too high
PLVoltage of DC bus-bar is too low
P0Compressor Min frequence in test state
P1Compressor rated frequence in test state
P2Compressor maximum frequence in test state
P3Compressor intermediate frequence in test state
P5Overcurrent protection of phase current for compressor
PUCharging malfunction of capacitor
P7Malfunction of module temperature sensor circuit
P8Module high temperature protection
H0Decrease frequency due to high temperature resistant during heating operation
H2Static dedusting protection
H3Overload protection for compressor
H4System is abnormal
H5IPM protection
H5Module temperature is too high
H6Internal motor (fan motor) do not operate
H7Desynchronizing of compressor
HCPFC protection
L3Outdoor DC fan motor malfunction
L9Power protection
LPIndoor unit and outdoor unit doesn't match
LCFailure startup
U1Malfunction of phase current detection circuit for compressor
U3Malfunction of voltage dropping for DC bus-bar
U5Malfunction of complete units current detection
U7The four-way valve is abnormal
U9Zerocrossing malfunction of outdoor unit
U8Zero-crossing inspection circuit malfunction of the IDU fan motor
Inventor Air Conditioner Remote Control
Inventor Air Conditioner Remote Control

Analysis or processing of some of the malfunction display:

  • Compressor discharge protection

Possible causes: shortage of refrigerant; blockage of air filter; poor ventilation or air flow short pass for condenser; the system has noncondensing gas (such as air, water etc.); blockage of capillary assy (including filter); leakage inside four-way valve causes incorrect operation; malfunction of compressor; malfunction of protection relay; malfunction of discharge sensor; outdoor temperature too high. Processing method: refer to the malfunction analysis in the above section.

  • Low voltage overcurrent protection

Possi ble cause: Sudden drop of supply voltage.

  • Communication malfunction

Processing method: Check if communication signal cable is connected reliably.

  • Sensor open or short circuit

Processing method: Check whether sensor is normal, connected with the corre sponding position on the controller and if damage of lead wire is found.

  • Compressor over load protection

Possible causes: insufficient or too much refrigrant; blockage of capillary and increase of suction temp.; improper running of compressor, burning in or stuck of bearing, damage of discharge valve; malfunction of protector. Processing method: adjust refrigerant amount; replace the capillary; replace the compressor; use universal meter to check if the contactor of compress or is fine when it is not overheated, if not replace the protector.

  • System malfunction

i.e.overload protection.When tube temperature(Check the temperature of outdoor heat exchanger when cooling and check the temperatur e of indoor heat exchanger when heating) is too high, protectionwill beactivated. Possi ble causes: Outdoor temperature is too high when cooling; insufficient outdoor air circulation; refrigerant flow malfunction. please refer to the malfunction analysis in the previous section for handling method .

  • IPM module protection

Processing method:Once the module malfunction happens,if it persists for a long time and can not be selfcanceled, cut off the power and turn off the unit,and then re-energize the unit again after about 10 min.After repeating the procedure for sever times, if the malfunction still exists,replace the module.

Comments

Post a Comment

Popular posts from this blog

Rittal Air Conditioner Error Codes

  System messages are shown on the display screen of the Comfort controller via the displays A1 to A20 and E0. Rittal Air Conditioner Error Codes Error Codes System message Possible cause A1 Enclosure door open Door open or door limit switch incorrectly positioned A2 Internal temperature of enclosure too high Cooling capacity inadequate/unit undersized. Error as a consequence of messages A03 to A17. A3 Filter monitoring Filter mat soiled A4 Ambient temperature too high/too low Ambient temperature outside of admissible operating range (+10°C to +60°C) A5 Icing hazard Operational display in case of icing hazard. A6 PSAH pressure-operated switch Ambient temperature too high A7 Evaporator coil Lack of coolant; sensor in front of or behind condenser defective. A8 Condensate warning Condensate discharge kinked or blocked A9 Condenser fan blocked or defective Blocked or defective A10 Evaporator fan blocked or defective Blocked or defective A11 Compressor Compressor overloaded A12 Condense...
Post a Comment
Read more

Midea VRF Error Codes

  R410A All DC Inverter V4 Plus R Series 50/60Hz Error Codes: V4 VRF:  Advanced 3-pipe technology enables  heat recovery  between indoor units for unprecedented economy and performance. It can simultaneously operate in cooling and heating mode when it is necessary to provide more freedom for operation. It compensates and adjusts when there are hot and cold rooms in the same building, depending on the direction of sunshine. As a result, it reduces annual power consumption. Midea VRF Error Codes Error Codes Problem E0 Communication error between outdoor units. Only display on the faulty slave unit, all the ODUs are in standby. E1 Phase sequence error. Display on the faulty unit, all the ODUs are in standby. E2 Communication error between indoors and the master unit. Only display on the master unit, all the ODUs are in standby. E4 Outdoor ambient temperature sensor (T4) and condenser pipe temperature sensor (T3/T5) error. Display on the faulty unit, all the ODUs are in ...
Post a Comment
Read more

York Chiller Error Codes and Troubleshooting

  Real Time Error Numbers York Chiller Error Codes and Troubleshooting Error Description 0 All Ok 1 Datum Type Ok Test Failed 2 English Text Too Long 3 Floating Point Exception 4 Get Packet Failed 5 Get Type Failed 6 Invalid Unit Conversion 7 Invalid Hardware Selection 8 Real Time Fault 9 Spanish Text Too Long 10 Thread Exited 11 Thread Failed 12 Thread Stalled 13 Io Board Reset 14 Bram Invalid 15 Bacnet Setup Failed Problem:  No display on panel – unit will not start Possible Cause: Main supply to control system OFF. Emergency stop device off. CB3 tripped. No supply to – T2 No 24VAC supply to power board. No +12V output from powerboard. Action: Switch on main supply if safe to do so. Check if control panel emergency stop switch and any remote emergency stop devices are in the OFF position. Turn to ON position (1) if safe to do so. Check CB3 Check 115VAC to L & 2. Check wiring from – T2 to powerboard and fuse. Replace powerboard or isolate excessive loa...
Post a Comment
Read more