Skip to main content

Hyundai Air Conditioner Error Codes

 Protection and Failure Display

  • When protection display is available, controller will show error code, digital LED shows error code and setting temperature by turns.
  • If there is more than one failure, it will show at first that in front of the error list.
  • Protection display function can be selected in hardware, and the default don’t display;
  • To insure of in and out communist is credibility, the failures relate to outdoor unit will remain failure state for 2 minutes max after recovered.
  • In all failures, only sensor failures don’t have to repower to cancel.
Hyundai Air Conditioner Error Codes
Hyundai Air Conditioner Error Codes

Error List

Error CodeLed CodeFailure Type
E0RUN, TIMER–both winkingIn and out communication failure
ECRUN, TIMER–both winkingOutdoor communication failure
E1RUN-1 time/8sOutdoor sensor
E2RUN-2 times /8sIndoor coil temperature sensor
E3RUN-3 times /8sOutdoor coil temperature sensor
E4RUN-4 times /8sSystem abnormity
E5RUN-5 times /8sType mismatch
E6RUN-6 times /8sIndoor fan motor
E7RUN-7 times /8sOutdoor temperature sensor
E8RUN-8 times /8sDischarge temperature sensor
E9RUN-9 times /8sInvert module abnormity
EFRUN-10 times /8sOutdoor fan motor (DC)
EARUN-11 times /8sCurrent sensor
EERUN-12 times /8sEEPROM failure
EPRUN-13 times /8sTop of compressor temperature switch
EURUN-14 times /8sVoltage sensor
Protection Display Code List
P1RUN-winking,TIMER-1 time/8shigher or lower voltage
P2RUN- winking,TIMER-2 times /8sOver current
P4RUN- winking,TIMER-4 times /8sDischarge temperature
P5RUN-light,TIMER-5 times /8sOver cooling in cooling mode
P6RUN- light,TIMER-6 times /8sOver heating in cooling mode
P7RUN- light,TIMER-7 times /8sOver heating in heating mode
P8RUN- light,TIMER-8 times /8sOutdoor temperature too high or low
P9RUN- winking,TIMER-9 times/8sDrive protection (Overload)
P0RUN- winking,TIMER-10 times/8sModule self protection
Hyundai Air Conditioner Remote Control
Hyundai Air Conditioner Remote Control

Outdoor Failure Display

There is a LED on outdoor power board, when compressor is running; it is normally light; when no feedback of signal to power board from compressor, it will wink by lighting 1s and going out 1s. If failures happened, it will light 0.5s, go out 0.5s, winking several times and go out 3s for a cycle to indicate failures. The failure list is the follow:

Hyundai Air Conditioner Outdoor Failure Display
Hyundai Air Conditioner Outdoor Failure Display
Wink timeFailure
1IPM protection
2higher or lower voltage
3Over current
4Discharge temperature too high
5Outdoor coil temperature too high
6Drive abnormity
7Communication abnormity with indoor unit
8Compressor over heat（switch on top of compressor）
9Outdoor air temperature sensor failure
10Outdoor coil temperature sensor failure
11Outdoor discharge pipe temperature sensor failure
12Voltage sensor failure
13Current sensor failure
14IPM abnormity
15Outdoor communication abnormity
16DC fan motor no feedback
17defrosting

Hyundai Air Conditioner Manual PDF

Comments

Post a Comment

Popular posts from this blog

Rittal Air Conditioner Error Codes

  System messages are shown on the display screen of the Comfort controller via the displays A1 to A20 and E0. Rittal Air Conditioner Error Codes Error Codes System message Possible cause A1 Enclosure door open Door open or door limit switch incorrectly positioned A2 Internal temperature of enclosure too high Cooling capacity inadequate/unit undersized. Error as a consequence of messages A03 to A17. A3 Filter monitoring Filter mat soiled A4 Ambient temperature too high/too low Ambient temperature outside of admissible operating range (+10°C to +60°C) A5 Icing hazard Operational display in case of icing hazard. A6 PSAH pressure-operated switch Ambient temperature too high A7 Evaporator coil Lack of coolant; sensor in front of or behind condenser defective. A8 Condensate warning Condensate discharge kinked or blocked A9 Condenser fan blocked or defective Blocked or defective A10 Evaporator fan blocked or defective Blocked or defective A11 Compressor Compressor overloaded A12 Condense...
Post a Comment
Read more

Midea VRF Error Codes

  R410A All DC Inverter V4 Plus R Series 50/60Hz Error Codes: V4 VRF:  Advanced 3-pipe technology enables  heat recovery  between indoor units for unprecedented economy and performance. It can simultaneously operate in cooling and heating mode when it is necessary to provide more freedom for operation. It compensates and adjusts when there are hot and cold rooms in the same building, depending on the direction of sunshine. As a result, it reduces annual power consumption. Midea VRF Error Codes Error Codes Problem E0 Communication error between outdoor units. Only display on the faulty slave unit, all the ODUs are in standby. E1 Phase sequence error. Display on the faulty unit, all the ODUs are in standby. E2 Communication error between indoors and the master unit. Only display on the master unit, all the ODUs are in standby. E4 Outdoor ambient temperature sensor (T4) and condenser pipe temperature sensor (T3/T5) error. Display on the faulty unit, all the ODUs are in ...
Post a Comment
Read more

LG VRF Error Codes – Multi V

  Error Codes; Indicate different types of unit failures, assist in self-diagnosis and to track the frequency of occurrence. Error codes are shown on the LED of indoor units, wired remote controller, the outdoor unit control board, and on the main screen of the LG Monitoring View (LGMV) Diagnostic Software. If two or more errors occur simultaneously, the lower error code number is displayed first. After error is resolved, the error code does not display. Error Display; The first, second, and third number on the LED indicates error number; the fourth number on LED indicates outdoor unit number. Examples: 211 = Error No. 21 on master unit, 213 = Error No. 21 on slave2 unit, Error No. 105 on master unit on compressor 1. Error Code Nomenclature Definitions; MICOM: Non-volatile memory chip where unit setup information is stored. EPROM: Non-volatile memory chip where device identification, size, and factory defined default component operating parameters are stored.   LG Multi V Erro...
2 comments
Read more