Skip to main content

Derby Air Conditioner Error Codes

 

Derby Air Conditioner Error Codes
Derby Air Conditioner Error Codes
Error CodesLed Status
E0EEPROM parameter error
E1Indoor / outdoor units communication protection
E2Zero-crossing signal error
E3Fan speed out of control
E5Open or short circuit of outdoor temperature sensor (T4)
E6Open or short circuit of room (T1) or evaporator temperature sensor (T2)
P0Outdoor PCB protection
P1Over voltage or too low voltage protection
P2Temperature protection of compressor top.
P4Inverter compressor drive error

Note: E4 & P3: Reserved function

Diagnosis and Solution

E0 (EEPROM parameter error) error diagnosis and solution

Circuit or software error on indoor PCB ⇒ Replace indoor PCB

E1 (indoor / outdoor units communication protection) error diagnosis and solution

E2 (zero-crossing signal error) diagnosis and solution

E3 (indoor fan speed out of control) diagnosis and solution

Troubleshooting

*Unit does not star:

  • Power cut. Wait for power to be restored.
  • Unit may have become unplugged. Check that plug is securely in wall receptacle.
  • Fuse may have blown. Replace the fuse.
  • Battery in Remote controller may have been exhausted. Replace the battery.
  • The time you have set with timer is incorrect. Wait or cancel timer setting.

*Unit not cooling or heating (Cooling/ heating models only) room very well while air flowing out from the air condtioner:

  • Inappropriate temperature setting. Set temperature correctly.
  • Air filter is blocked. Clean the air filter.
  • Doors or Windows are open. Close the doors or windows.
  • Air inlet or outlet of indoor or outdoor unit has been blocked. Clear obstructions away first, then restart the unit.
  • Compressor 3 minutes protection has been activated. Wait.

If the trouble has not been corrected, please contact a local dealer or the nearest customer service center. Be sure to inform them of the detailed malfunctions and unit model.

Derby AC Self Diagnostic Failure Indications
Derby AC Self Diagnostic Failure Indications

 

Derby Air Conditioner Manual PDF-1

Derby Air Conditioner Manual PDF-2

Derby Air Conditioner Manual PDF-3

Comments

Post a Comment

Popular posts from this blog

Rittal Air Conditioner Error Codes

  System messages are shown on the display screen of the Comfort controller via the displays A1 to A20 and E0. Rittal Air Conditioner Error Codes Error Codes System message Possible cause A1 Enclosure door open Door open or door limit switch incorrectly positioned A2 Internal temperature of enclosure too high Cooling capacity inadequate/unit undersized. Error as a consequence of messages A03 to A17. A3 Filter monitoring Filter mat soiled A4 Ambient temperature too high/too low Ambient temperature outside of admissible operating range (+10°C to +60°C) A5 Icing hazard Operational display in case of icing hazard. A6 PSAH pressure-operated switch Ambient temperature too high A7 Evaporator coil Lack of coolant; sensor in front of or behind condenser defective. A8 Condensate warning Condensate discharge kinked or blocked A9 Condenser fan blocked or defective Blocked or defective A10 Evaporator fan blocked or defective Blocked or defective A11 Compressor Compressor overloaded A12 Condense...
Post a Comment
Read more

Midea VRF Error Codes

  R410A All DC Inverter V4 Plus R Series 50/60Hz Error Codes: V4 VRF:  Advanced 3-pipe technology enables  heat recovery  between indoor units for unprecedented economy and performance. It can simultaneously operate in cooling and heating mode when it is necessary to provide more freedom for operation. It compensates and adjusts when there are hot and cold rooms in the same building, depending on the direction of sunshine. As a result, it reduces annual power consumption. Midea VRF Error Codes Error Codes Problem E0 Communication error between outdoor units. Only display on the faulty slave unit, all the ODUs are in standby. E1 Phase sequence error. Display on the faulty unit, all the ODUs are in standby. E2 Communication error between indoors and the master unit. Only display on the master unit, all the ODUs are in standby. E4 Outdoor ambient temperature sensor (T4) and condenser pipe temperature sensor (T3/T5) error. Display on the faulty unit, all the ODUs are in ...
Post a Comment
Read more

Innovair Air Conditioner Error Codes

 innovair  prestige  inverter mini split system: Innovair Air Conditioner Error Codes Error Codes Problem E2 Anti-freezing protection E3 Block or Low pressure of refrigerant system E4 Compressor exhaust high temperature protection E5 AC over-current protection E6 Communication failure between indoor unit and outdoor unit E8 Anti-high temperature protection H4 Anti-high temperature protection H6 No feedback of indoor fan motor C5 Jumper cap malfunction protection LP Indoor unit and outdoor unit doesn't match L3 Outdoor DC fan motor malfunction L9 Power protection Fo Gathering refrigerant F1 Indoor ambient sensor open or short circuit F2 Indoor tube sensor open or short circuit F3 Outdoor ambient sensor open or short circuit F4 Outdoor tube sensor open or short circuit F5 Exhaust sensor open or short circuit F6 Overload limit / drop frequency F8 Over current limit / drop frequency F9 High exhaust temperature limit / drop frequency F0 Refrigerant leakage protection FH Anti-f...
Post a Comment
Read more