Skip to main content

Blue Star Air Conditioner Error Codes

 Blue Star Ductable AC, Window AC, Inverter AC error codes list;

Blue Star Air Conditioner Error Codes
Blue Star Air Conditioner Error Codes
Error CodesProblem
E0IDU EEPROM error
E1ODU coil medium-high error
E2IDU coil frozen protection
E4Discharge temperature high error
E5AC input over current protection
E6Communication error
E8Zero crossing error
EEODU EEPROM error
ECRefrigerant leak detection
F1Indoor room temperature sensor error
F2IDU coil temperature sensor error
F3Ambient temperature sensor error
F4ODU coil temperature sensor error
F5ODU discharge temperature sensor error
P3Drive phase current over load fault
P4DC bus bar high voltage and low voltage protection
P7IPM error
P5Compressor phase current protection
P8IPM over high temperature protection
PHAC over voltage and under voltage protection
L1Drive phase voltage over load protection
L2Drive phase voltage over low protection
L3Outdoor DC fan fault
L4Phase current sampling abnormal
LCCompressor out of step fault
LCCompressor startup failure
H6IDU fan motor error

Troubleshooting

Symptoms: Unit does not start

Possible Causes: MCB has tripped

Suggested Remedy: Reset MCB

Symptoms: Fuse has burnt

Possible Causes:

  1. Input voltage to the stabiliser is below acceptable range
  2. Replace fuse wire

Suggested Remedy:

  1. If the input voltage to the stabiliser is below the acceptable range, the airconditioner will not turn on

Symptoms: Unit does not cool even after the normal time delay of approx. 2 minutes

Possible Causes:

  1. Compressor is off (not in Auto or Cool Mode)
  2. The airflow paths of either or both the indoor & outdoor units are not free
  3. The air-filter is not clean

Suggested Remedy:

  1. Use the remote to turn the compressor on
  2. Remove all obstructions to make the airflow paths free
  3. Clean the air-filter

NOTE: If the unit still does not work, or if any other types of symptoms are encountered, shut off the mains (switch fuse unit) and call the service engineer/technician.

Blue Star Air Conditioner Remote Control

Blue Star Air Conditioner Remote Control
Blue Star Air Conditioner Remote Control

 

Blue Star Air Conditioner Manual PDF

Comments

Post a Comment

Popular posts from this blog

Rittal Air Conditioner Error Codes

  System messages are shown on the display screen of the Comfort controller via the displays A1 to A20 and E0. Rittal Air Conditioner Error Codes Error Codes System message Possible cause A1 Enclosure door open Door open or door limit switch incorrectly positioned A2 Internal temperature of enclosure too high Cooling capacity inadequate/unit undersized. Error as a consequence of messages A03 to A17. A3 Filter monitoring Filter mat soiled A4 Ambient temperature too high/too low Ambient temperature outside of admissible operating range (+10°C to +60°C) A5 Icing hazard Operational display in case of icing hazard. A6 PSAH pressure-operated switch Ambient temperature too high A7 Evaporator coil Lack of coolant; sensor in front of or behind condenser defective. A8 Condensate warning Condensate discharge kinked or blocked A9 Condenser fan blocked or defective Blocked or defective A10 Evaporator fan blocked or defective Blocked or defective A11 Compressor Compressor overloaded A12 Condense...
Post a Comment
Read more

Midea VRF Error Codes

  R410A All DC Inverter V4 Plus R Series 50/60Hz Error Codes: V4 VRF:  Advanced 3-pipe technology enables  heat recovery  between indoor units for unprecedented economy and performance. It can simultaneously operate in cooling and heating mode when it is necessary to provide more freedom for operation. It compensates and adjusts when there are hot and cold rooms in the same building, depending on the direction of sunshine. As a result, it reduces annual power consumption. Midea VRF Error Codes Error Codes Problem E0 Communication error between outdoor units. Only display on the faulty slave unit, all the ODUs are in standby. E1 Phase sequence error. Display on the faulty unit, all the ODUs are in standby. E2 Communication error between indoors and the master unit. Only display on the master unit, all the ODUs are in standby. E4 Outdoor ambient temperature sensor (T4) and condenser pipe temperature sensor (T3/T5) error. Display on the faulty unit, all the ODUs are in ...
Post a Comment
Read more

Innovair Air Conditioner Error Codes

 innovair  prestige  inverter mini split system: Innovair Air Conditioner Error Codes Error Codes Problem E2 Anti-freezing protection E3 Block or Low pressure of refrigerant system E4 Compressor exhaust high temperature protection E5 AC over-current protection E6 Communication failure between indoor unit and outdoor unit E8 Anti-high temperature protection H4 Anti-high temperature protection H6 No feedback of indoor fan motor C5 Jumper cap malfunction protection LP Indoor unit and outdoor unit doesn't match L3 Outdoor DC fan motor malfunction L9 Power protection Fo Gathering refrigerant F1 Indoor ambient sensor open or short circuit F2 Indoor tube sensor open or short circuit F3 Outdoor ambient sensor open or short circuit F4 Outdoor tube sensor open or short circuit F5 Exhaust sensor open or short circuit F6 Overload limit / drop frequency F8 Over current limit / drop frequency F9 High exhaust temperature limit / drop frequency F0 Refrigerant leakage protection FH Anti-f...
Post a Comment
Read more