Skip to main content

Chunlan Air Conditioner Error Codes

 Microprocessor-based controller of this unit features troubleshooting and protection display  functions.

Chunlan Air Conditioner Error Codes
Chunlan Air Conditioner Error Codes
Error CodesProblem
E0High pressure protection
E1Antifreeze protection
E2ID ambient temp probe short circuit
E3ID pipe temp probe short circuit
E4OD pipe temp probe short circuit
E5Communication failure
E6Phase sequence protection
E7Overcurrent protection
E8Load relief protection
E9Low pressure protection

In case of repeated protections of air conditioner, cut off power supply and have failure corrected by specialty maintenance personnel, before restarting the machine.

Chunlan Air Conditioner Error Codes / E1-E2-E3-E4
Chunlan Air Conditioner Error Codes / E0-E1-E2-E3-E4-E5-E6-E7-E8-E9

Common Troubleshooting

In case of AC failure, immediately cut off power supply. Check the following before requesting maintenance:

Failure: Machine not operating

Causes:

  1. Power off
  2. Power not meeting requirement
  3. Molten fuse or open CB

Correction measures:

  1. Use when power is resumed
  2. Check power supply before use
  3. Replace fuse or close circuit breaker

Failure: Machine operating at poor cooling/heating efficiency, or not cooling or heating

Causes:

  1. Clogged air strainer
  2. ID or OD unit air intake clogged
  3. Improper temp control setting
  4. Open door/window

Correction measures:

  1. Clean air strainer
  2. Remove obstacles
  3. Reset temperature control
  4. Close doors/windows

This air duct type air conditioner is our latest home (commercial) centralized air conditioning product.

This product features high efficiency, energy saving, mild and silent operation, computerized intelligent control and healthy fresh air etc.

In addition, wire and wireless controls are provided for easy operation.

The product can be widely used in large area, multi-room composite compartment/houses, villa, and medium and small restaurants, bars, leisure and recreation sites.

Chunlan Air Conditioner Ordinary wire controller
Chunlan Air Conditioner Ordinary wire controller

Note:

1. For relevant models and parameters provided in this manual, actual products and nameplate information shall govern;

2. This manual has been carefully checked. In case of printing error, our company shall not bear responsibility for the consequences.

3. Our company is in constant technology advancement and product series and sizes will be adjusted from time to time. Please note information of our new products.

Chunlan Air Conditioner Manual PDF


Comments

Post a Comment

Popular posts from this blog

Rittal Air Conditioner Error Codes

  System messages are shown on the display screen of the Comfort controller via the displays A1 to A20 and E0. Rittal Air Conditioner Error Codes Error Codes System message Possible cause A1 Enclosure door open Door open or door limit switch incorrectly positioned A2 Internal temperature of enclosure too high Cooling capacity inadequate/unit undersized. Error as a consequence of messages A03 to A17. A3 Filter monitoring Filter mat soiled A4 Ambient temperature too high/too low Ambient temperature outside of admissible operating range (+10°C to +60°C) A5 Icing hazard Operational display in case of icing hazard. A6 PSAH pressure-operated switch Ambient temperature too high A7 Evaporator coil Lack of coolant; sensor in front of or behind condenser defective. A8 Condensate warning Condensate discharge kinked or blocked A9 Condenser fan blocked or defective Blocked or defective A10 Evaporator fan blocked or defective Blocked or defective A11 Compressor Compressor overloaded A12 Condense...
Post a Comment
Read more

Midea VRF Error Codes

  R410A All DC Inverter V4 Plus R Series 50/60Hz Error Codes: V4 VRF:  Advanced 3-pipe technology enables  heat recovery  between indoor units for unprecedented economy and performance. It can simultaneously operate in cooling and heating mode when it is necessary to provide more freedom for operation. It compensates and adjusts when there are hot and cold rooms in the same building, depending on the direction of sunshine. As a result, it reduces annual power consumption. Midea VRF Error Codes Error Codes Problem E0 Communication error between outdoor units. Only display on the faulty slave unit, all the ODUs are in standby. E1 Phase sequence error. Display on the faulty unit, all the ODUs are in standby. E2 Communication error between indoors and the master unit. Only display on the master unit, all the ODUs are in standby. E4 Outdoor ambient temperature sensor (T4) and condenser pipe temperature sensor (T3/T5) error. Display on the faulty unit, all the ODUs are in ...
Post a Comment
Read more

LG VRF Error Codes – Multi V

  Error Codes; Indicate different types of unit failures, assist in self-diagnosis and to track the frequency of occurrence. Error codes are shown on the LED of indoor units, wired remote controller, the outdoor unit control board, and on the main screen of the LG Monitoring View (LGMV) Diagnostic Software. If two or more errors occur simultaneously, the lower error code number is displayed first. After error is resolved, the error code does not display. Error Display; The first, second, and third number on the LED indicates error number; the fourth number on LED indicates outdoor unit number. Examples: 211 = Error No. 21 on master unit, 213 = Error No. 21 on slave2 unit, Error No. 105 on master unit on compressor 1. Error Code Nomenclature Definitions; MICOM: Non-volatile memory chip where unit setup information is stored. EPROM: Non-volatile memory chip where device identification, size, and factory defined default component operating parameters are stored.   LG Multi V Erro...
2 comments
Read more