Skip to main content

Beko AC Error Codes and Troubleshooting

 When air conditioner status ib abnormal, temperature indicator on indoor unit will blink to display corresponding error code. Please refer to blow list for identification of error.

Beko AC Error Codes
Beko AC Error Codes
Error CodesCause
H1Means defrosting status. It's the normal phenomenon.
E5It can be eliminated after restarting the unit. If not, please contact qualified professionals for service.
U8It can be eliminated after restarting the unit. If not, please contact qualified professionals for service.
H6It can be eliminated after restarting the unit. If not, please contact qualified professionals for service.
C5Please contact qualified professionals for service.
F1Please contact qualified professionals for service.
F2Please contact qualified professionals for service.

Note: If there’re other error codes, please contact qualified professionals for service.

Introduction for icons on display screen
Introduction for icons on display screen

Warning

When below phenomenon occurs, please turn off air conditioner and disconnect power immediately, and then contact the dealer or qualified professionals for service.

  • Power cord is overheating or damaged.
  • There’s abnormal sound during operation.
  • Circuit break trips off frequently.
  • Air conditioner gives off burning smeel.
  • Indoor unite is leaking.

*Do not repair or refit the air conditioner by yourself.
*If the air conditioner operates under abnormal conditions, it may cause malfunction, electric shock or fire hazard.

Beko Air Conditiner Remote Control
Beko Air Conditiner Remote Control

Beko AC Troubleshooting

Beko AC Error Codes and Troubleshooting
Beko AC Error Codes and Troubleshooting

Check the following points before requesting repairs or service. If the fault persists, please contact your dealer or service center.

*The air conditioner does no operate.
-Have you made a mistake in timer operation?
-Has the fuse blown or has the circuit breaker been tripped?

*The room has a peculiar odor.
-Check that this is not a damp smell exuded by the walls, carpet, furniture, or cloth items in the room.

*It seems that condensation is leaking from the air conditioner.
-Condensation occurs when the airflow from the air conditioner cools the warm room air.

*Air conditioner does not operate for about 3 minutes when restarted.
-This is the protector of the mechanism.
-Wait about three minutes and operation will begin.

*Does not cool or heat effectively.
– Is the air filter dirty? See air filter cleaning instructions.
– Has the temperature been set incorrectly?
– Are the indoor unit’s air inlet or outlet vents obstructed?

*The air conditioner operation is noisy.
-For a noise that sounds like water flowing. This is the sound of freon flowing inside the air conditioner unit.
-For a noise that sounds like the compressed air releasing into atmosphere. This is the sound of the dehumidifying water being processed inside the air conditioning unit.

*Remote control display is faint, or no display at all.
-Are the batteries depleted?
-Are the batteries inserted in the opposite (+) and (-) directions?

*Crack sound is heard.
This sound is generated by the expansion/constriction of the front panel, etc. due to changes of temperature.

Split Air Conditioner User Manual PDF

Comments

Post a Comment

Popular posts from this blog

Rittal Air Conditioner Error Codes

  System messages are shown on the display screen of the Comfort controller via the displays A1 to A20 and E0. Rittal Air Conditioner Error Codes Error Codes System message Possible cause A1 Enclosure door open Door open or door limit switch incorrectly positioned A2 Internal temperature of enclosure too high Cooling capacity inadequate/unit undersized. Error as a consequence of messages A03 to A17. A3 Filter monitoring Filter mat soiled A4 Ambient temperature too high/too low Ambient temperature outside of admissible operating range (+10°C to +60°C) A5 Icing hazard Operational display in case of icing hazard. A6 PSAH pressure-operated switch Ambient temperature too high A7 Evaporator coil Lack of coolant; sensor in front of or behind condenser defective. A8 Condensate warning Condensate discharge kinked or blocked A9 Condenser fan blocked or defective Blocked or defective A10 Evaporator fan blocked or defective Blocked or defective A11 Compressor Compressor overloaded A12 Condense...
Post a Comment
Read more

Midea VRF Error Codes

  R410A All DC Inverter V4 Plus R Series 50/60Hz Error Codes: V4 VRF:  Advanced 3-pipe technology enables  heat recovery  between indoor units for unprecedented economy and performance. It can simultaneously operate in cooling and heating mode when it is necessary to provide more freedom for operation. It compensates and adjusts when there are hot and cold rooms in the same building, depending on the direction of sunshine. As a result, it reduces annual power consumption. Midea VRF Error Codes Error Codes Problem E0 Communication error between outdoor units. Only display on the faulty slave unit, all the ODUs are in standby. E1 Phase sequence error. Display on the faulty unit, all the ODUs are in standby. E2 Communication error between indoors and the master unit. Only display on the master unit, all the ODUs are in standby. E4 Outdoor ambient temperature sensor (T4) and condenser pipe temperature sensor (T3/T5) error. Display on the faulty unit, all the ODUs are in ...
Post a Comment
Read more

LG VRF Error Codes – Multi V

  Error Codes; Indicate different types of unit failures, assist in self-diagnosis and to track the frequency of occurrence. Error codes are shown on the LED of indoor units, wired remote controller, the outdoor unit control board, and on the main screen of the LG Monitoring View (LGMV) Diagnostic Software. If two or more errors occur simultaneously, the lower error code number is displayed first. After error is resolved, the error code does not display. Error Display; The first, second, and third number on the LED indicates error number; the fourth number on LED indicates outdoor unit number. Examples: 211 = Error No. 21 on master unit, 213 = Error No. 21 on slave2 unit, Error No. 105 on master unit on compressor 1. Error Code Nomenclature Definitions; MICOM: Non-volatile memory chip where unit setup information is stored. EPROM: Non-volatile memory chip where device identification, size, and factory defined default component operating parameters are stored.   LG Multi V Erro...
2 comments
Read more